DESCRIPTION. PRODUCT NO. 10000 PRO-COAT is an ultra durable 100% acrylic elastomeric roof coating with advanced weathering technology. PRODUCT NO. 10000 PRO-COAT maintains its physical properties even after prolonged exposure to UV light. PRODUCT NO. 10000 PRO-COAT offers excellent flow characteristics, making for a premium application process. Its bright white finish enables it to deflect the sun’s heat and harmful UV rays, protecting the roof substrate and lowering energy bills. PRODUCT NO. 10000 PRO-COAT forms a thick, rubber-like shield that expands and contracts greater than 450% to prevent cracking and slow the aging process. PRODUCT NO. 10000 PRO-COAT resists cracking, peeling, and mildew while providing excellent protection against extreme weather.
USES. PRODUCT NO. 10000 PRO-COAT can be used over spray polyurethane foam, asphalt, tar, hot-applied built-up roofing, granulated cap sheet, and metal roofing systems. PRODUCT NO. 10000 PROCOAT can be directly applied over most previously coated roof surfaces. PRODUCT NO. 10000 PRO-COAT should not be applied over 100% silicone. When applying over asphalt based substrates, aluminum roof coating, TPO, or EPDM follow surface preparation instructions below.
SURFACE PREPARATION. Roof substrates must be clean, dry, free of all debris, and any contaminants which would impede proper adhesion. A pressure wash is recommended, if a pressure washer is not available a cleaning agent should be used in conjunction with hose and broom washing. In addition to pressure washing, a wire brush should be used to remove any surface rust on metal roofing systems. Metal panels where the structural integrity has been compromised should be removed and replaced with like panels. A bleach and water solution (1 part bleach to 2 parts water) should be used to treat any roof areas that have mildew or algae. All roof surfaces should be thoroughly cleaned and allowed to dry completely prior to application of any Tucson Rubberized Coatings products. When applying PRODUCT NO. 10000 PRO-COAT over asphalt based substrates, once coat of PRODUCT NO. 295-G STAIN SHIELD is recommended to avoid bleed-through. Over aluminum roof coating, one coat of PRODUCT NO. 295-G STAIN SHIELD or PRODUCT NO. 297-X X-TREME must be applied prior to the application of PRODUCT NO. 10000 PRO-COAT. All large cracks and seams should be repaired by embedding one layer of polyester fabric between two layers of PRODUCT NO. 502 ACRYLIC MASTIC or PRODUCT NO. 510 ACRYLIC MASTIC prior to application of PRODUCT NO. 10000 PRO-COAT. To achieve proper adhesion over TPO, PVC, or EPDM, one coat of 297-X X-TREME should be applied prior to any Tucson Rubberized Coatings repair or top coat products.
APPLICATION. Proper protective clothing and PPE should be worn when applying products. It is normal to see a small amount of separation when first opening a pail. If necessary, gently mix the product with a roller frame or paddle mixer, being careful to not introduce air into the product during mixing. Product can be applied by roller (3/4 – 1 1/4″ nap), brush, and spray equipment capable of 2000 – 3000 PSI and 1 – 3 GPM of output. For best results when spraying, an 8-31 – 8-41 reversible spray is recommended. Do not dilute product. Tucson Rubberized Coatings Products should not be applied when freezing temperatures or rain is expected within 24 hours of completed application. During application, roof surface temperatures should be between 40 and 115 degrees Fahrenheit, with no moisture present.
Allow 24 to 72 hours depending on weather conditions and applications rate of curing prior to application of second coat. Do not apply unless temperature is 55°F and rising. Do not apply when rain or frost is forecast within 24 hours after application. However, conditions of high humidity will prevent curing in the usual four hours. Avoid heavy foot traffic.
DO NOT APPLY TO ANY SURFACES THAT CONTAIN SILICONE.
CLEAN-UP. Clean brushes, tools and other equipment with warm soapy water immediately after use. Dried film may require paint remover.
|Dimensions||13 × 13 × 16 cm|
|Weight per Gallon||
|Solids by Weight*||
|Drying Time (50% Relative Humidity & 70°F)||
Touch: 4 hrs, Firm: 12 hrs
> 400 PSI
Percentages stated are + or – 5%
|Approx. Shipping Weights:||
(All approximate weights include container)